Classification yard Information
This article needs additional citations for verification. (February 2013) ( Learn how and when to remove this template message)
A classification yard ( American and Canadian English) or marshalling yard ( British, Hong Kong, Indian, Australian and Canadian English) is a railway yard found at some freight train stations, used to separate railway cars onto one of several tracks. First the cars are taken to a track, sometimes called a lead or a drill. From there the cars are sent through a series of switches called a ladder onto the classification tracks. Larger yards tend to put the lead on an artificially built hill called a hump to use the force of gravity to propel the cars through the ladder.
Freight trains that consist of isolated cars must be made into trains and divided according to their destinations. Thus the cars must be shunted several times along their route in contrast to a unit train, which carries, for example, cars from the plant to a port, or coal from a mine to the power plant. This shunting is done partly at the starting and final destinations and partly (for long-distance-hauling) in classification yards.
Flat yards are constructed on flat ground, or on a gentle slope. Freight cars are pushed by a locomotive and coast to their required location. 
Hump yards are the largest and most effective classification yards, with the largest shunting capacity, often several thousand cars a day. The heart of these yards is the hump—a lead track on a small hill over which an engine pushes the cars. Single cars, or a block of coupled cars, are uncoupled just before or at the crest of the hump, and roll by gravity onto their destination tracks in the tracks where the cars are sorted, called the classification bowl. 
The speed of the cars rolling down from the hump into the classification bowl must be regulated according to whether they are full or empty, heavy or light freight, varying number of axles, whether there are few or many cars on the classification tracks, and varying weather conditions, including temperature, wind speed and direction. As concerns speed regulation, there are two types of hump yards—without or with mechanisation by retarders. In the old non-retarder yards braking was usually done in Europe by railroaders who laid skates onto the tracks. The skate or wheel chock was manually (or, in rare cases, mechanically) placed on one or both of the rails so that the treadles or rims of the wheel or wheels caused frictional retardation and resulted in the halting of the railway car. In the United States this braking was done by riders on the cars. In the modern retarder yards this work is done by mechanized "rail brakes" called retarders, which brake the cars by gripping the wheels. They are operated either pneumatically or hydraulically. Pneumatic systems are prevalent in the United States, France, Belgium, Russia and China, while hydraulic systems are used in Germany, Italy and the Netherlands.[ citation needed]
Classification bowls in Europe typically consist of 20 to 40 tracks, divided into several fans or balloons of tracks, usually with eight classification tracks following a retarder in each one, often 32 tracks altogether. In the United States, many classification bowls have more than 40 tracks, which are often divided into six to ten classification tracks in each balloon loop.
Bailey Yard in North Platte, Nebraska, United States, the world's largest classification yard, is a hump yard. Other large American hump yards include Argentine Yard in Kansas City, Kansas, the second-largest in the world, Robert Young Yard in Elkhart, Indiana, Clearing Yard in Chicago, Illinois, Englewood Yard in Houston, Texas, and Waycross Rice Yard in Waycross, Georgia. Notably, in Europe, Russia and China, all major classification yards are hump yards. Europe's largest hump yard is that of Maschen near Hamburg, Germany; it is only slightly smaller than Bailey Yard. The second largest is in the port of Antwerp, Belgium. Most hump yards are single yards with one classification bowl, but some, mostly very large, hump yards have two of them, one for each direction, thus are double yards, such as the Maschen, Antwerp, Clearing, and Bailey yards. According to the PRRT&HS PRR Chronology, the first hump yard in the United States was opened May 11, 1903 as part of the Altoona Yards at Bells Mills (East Altoona).[ citation needed] Other sources report the PRR yard at Youngwood, PA which opened in the 1880s to serve the Connellsville coke fields as the first U.S. hump yard.[ citation needed]
Gravity yards are operated similarly to hump yards but, in contrast to the latter, the whole yard is set up on a continuous falling gradient. When they were invented in the 19th century, saving shunting engines and instead letting the cars roll by gravity was seen as a major benefit, whereas the larger amount of manual work required to stop the rolling cars in the classification tracks was judged to be not that important. Gravity yards were a historical step in the development of classification yards and were later judged as inferior to hump yards, because it became clear that shunting engines were needed anyway (at least in inclement weather like strong winds or icy temperatures when the oil in the bearings became thick), and because manual labour was getting relatively more and more expensive. Thus, only few gravity yards were ever built, sometimes requiring massive earthwork (one example is the first German gravity yard at Dresden).
Most gravity yards were built in Germany and Great Britain, a few also in some other European countries, for example Łazy yard near Zawiercie on the Warsaw-Vienna Railway (in Poland). In the USA, there were only very few old gravity yards; one of the few gravity yards in operation today is CSX's Readville Yard south of Boston, Massachusetts.
Almost all gravity yards have been retrofitted with humps and are worked as hump yards. Examples include Dresden Friedrichstadt and Nürnberg ( Nuremberg) Rbf (Rbf: Rangierbahnhof, "classification yard"), both in Germany.
This section contains what may be an unencyclopedic or excessive gallery of images.Learn how and when to remove this template message)(
- International Railway Journal (IRJ), New York. Special editions about hump yards in various countries: issues II/66, II/70, VI/75, II/80.
- Armstrong, John H. (1998). The Railroad: What It Is, What It Does (4th ed.). Omaha, NE: Simmons-Boardman. ISBN 978-0-911382-04-4.
- Rhodes, Michael: The Illustrated History of British Marshalling Yards. Sparkford: Haynes Oxford Publishing & Co, 1988. ISBN 0-86093-367-9. Out of print.
- Kraft, Edwin: The Yard: Railroading's Hidden Half. In: Trains (vol. 62) 2002. Part I: VI/02, pp. 46–67; part II: VII/02, pp. 36–47. ISSN 0041-0934.
- Wegner, Robert: Classification yards. Map of the Month. In: Trains IV/2003, pp. 42–43.
- Rhodes, Michael: North American Railyards. St. Paul (USA): Motorbooks International (MBI Publishing Company) 2003. ISBN 0-7603-1578-7.
|Wikimedia Commons has media related to Classification yards.|
- Refuge Sidings, Exchange Sidings and Marshalling Yards
- Yard Duty Freight Yard Simulation game
- Villon – transportation terminal simulation tool
- Time-lapse video of German hump-shunting yard operation